4 Point Inspections in Putnam County, FL

A 4-point inspection is often a required inspection in order to obtain, or to maintain, insurance coverage. The requirements were designed by insurance companies in order to get a better understanding of the four main aspects they are insuring: heating and cooling (HVAC), roof, plumbing, and electrical. It is a short, focused report on those four systems and nothing else.

A 4-point inspection is an insurance underwriting document, not a buyer's inspection. It reports on four systems only: roof, electrical, plumbing, and HVAC. Requirements vary by carrier, so confirm with your insurance agent, your realtor or your lender whether a 4-point is needed for the policy you are placing or renewing, and we can include it with your inspection when one is called for. The report answers a narrow question: are these four systems in serviceable condition with reasonable remaining life, and is there anything present that the carrier treats as an unacceptable risk. It says nothing about the foundation, the windows, the attic ventilation, or whether the house is a good buy. If you are purchasing, you want a full home inspection as well. The 4-point is a document your agent needs, not a substitute for due diligence.

The electrical section is where policies most often die, and the cause is usually the panel brand. Federal Pacific Electric Stab-Lok, Zinsco, Challenger, and Pushmatic panels are widely flagged by Florida carriers because of documented breaker failure-to-trip histories. Many carriers will decline outright rather than write with a condition. Sylvania-branded equipment associated with the Zinsco lineage draws the same scrutiny. The practical answer is a panel replacement by a licensed electrician under permit, typically a four-figure job, done before the inspection rather than after a declination is on record. The section also covers service capacity, evidence of aluminum branch circuit wiring in the smaller conductor sizes used in the mid-1960s to mid-1970s, knob-and-tube remnants, double-tapped breakers, open splices, and the presence of GFCI and AFCI protection.

Plumbing turns on material. Polybutylene supply piping, common in homes built from roughly the late 1970s to the mid-1990s and recognizable by its grey (sometimes blue or black) flexible tubing, is flagged by most Florida carriers. The pipe itself is not usually where it fails. Failures concentrate at the fittings and crimp connections, where oxidants in treated municipal water degrade the material from the inside and the joint lets go with no warning and no drip beforehand. That is why insurers treat it as a whole-system replacement issue rather than a repair issue. Galvanized steel supply lines are the other flag, scaling closed from the inside and reducing flow long before they leak. Cast iron drain lines, common in Jacksonville's older neighborhoods, get noted for scaling and channeling.

On the roof, insurers care about remaining service life far more than about age as a number. A twelve-year-old architectural shingle roof in good condition with clean flashings, no granule loss to speak of, and no soft decking can underwrite fine. A nine-year-old three-tab roof that has been through two named storms, with lifted tabs, exposed fasteners, and a failed pipe boot, may not. As a working rule most carriers want to see at least three years of remaining life, and many will not bind on a shingle roof past roughly the fifteen-to-twenty year mark regardless of appearance, with longer tolerances for tile and metal. The inspection documents covering type, layers, visible damage, active leakage, and an estimate of remaining life with photographs supporting the call.

HVAC is the most forgiving of the four, but not automatically. The report captures system type, age from the data plate, whether it produces adequate temperature split in operation, condition of the condensate handling, and whether the equipment has obvious deferred maintenance or improvised repairs. In Northeast Florida a fifteen-year-old air handler in an attic with a rusted primary pan, a plugged secondary line, and no float switch is a claim waiting to happen and carriers know it. Homes still heated by an original wall furnace or with no functioning heat source at all can draw a condition. Straightforward preparation helps: have the system serviced, clear the condensate lines, and make sure the equipment closet or attic platform is accessible on inspection day.

What you can actually do before the inspection is more than most people think. Replace a flagged panel. Get quotes on repiping if you have polybutylene, because a carrier will want a completion date, not an intention. Have a roofer address boots, flashings, and lifted shingles, and keep the invoice. Clear access to the panel, the attic, the water heater, and the air handler. If there was unpermitted work in the past, especially a water heater swap or a panel change, pull the permit record now. A 4-point takes roughly forty-five minutes to an hour and a half. The report is emailed with photographs of each system, and it is far easier to fix a problem before it exists on paper than to argue with an underwriter afterward.